Tesztek

F-Gas English Low GWP

Minden kérdés
HFC | Flammable | CO₂ | NH₃
Könnyű kérdések | Közepes nehézségű kérdések | Nehéz kérdések

1

Könnyű

What is the base unit of mass according to the International System of Units (Système International d’Unités)?


t
N
Pound
kg

2

Közepes

What process takes place in the condenser of a refrigeration system?


In the condenser, the refrigerant releases the heat absorbed in the evaporator into the surroundings.
The medium flowing through the evaporator (glycol, water) condenses, whilst the refrigerant evaporates.
The refrigerant releases the heat absorbed in the compressor via the condenser
Hot refrigerant vapour is pumped from the compressor to the condenser, where it is cooled and then condensed. In this heat exchanger, the resulting liquid refrigerant is also slightly subcooled.

3

Közepes

What determines the condensation temperature of an air-cooled unit?


On the evaporation (boiling) temperature.
On the ambient temperature.
On the superheat temperature.
On the compressor and discharge temperatures

4

Közepes

Is energy required when heat is transferred from the condenser to the surroundings?


The heat flow balances the energy input.
Yes, in every case.
No, because according to the second law of thermodynamics, thermal energy always flows from a body at a higher temperature to a body at a lower temperature.
Yes, but only when using HFC refrigerants.

5

Közepes

What should you pay attention to during the operation of the condenser?


You should ensure the general maintenance of the condenser and keep the heat exchange surfaces clean.
Care should be taken to ensure that the air temperature at the condenser inlet is lower than the air temperature at the condenser outlet.
Ensure that the air temperature at the condenser outlet is higher than the condensation temperature.
Pay attention to the fan’s operation and the ambient temperature.

6

Közepes

What criteria should be considered when selecting a suitable condenser?


Condensers should be selected based on your own experience, and the condenser’s geometric parameters should be taken into account.
First and foremost, you should consider the operating noise level of the fans, the diameter of the connection pipes and the colour scheme.
The required capacity of the condenser and the technical specifications declared by the manufacturer must be taken into account.
These include size and the number of fans. The geometric parameters of the condenser must be taken into account.

7

Közepes

How do contaminants (dust, particulates, deposits) affect the performance and efficiency of heat exchange surfaces in condensers?


Contaminants do not significantly affect the efficiency and effectiveness of the heat exchange surfaces in condensers.
Contaminants restrict heat transfer (reducing the heat transfer coefficient) and cause an increase in condensing temperature and pressure, which in turn leads to a reduction in the condenser’s efficiency.
Contaminants increase the heat transfer area and reduce the condensing pressure.
Contaminants restrict heat transfer (reducing the heat transfer coefficient) and cause a reduction in condensing pressure.

8

Közepes

If an air-cooled condenser becomes contaminated, will the condensation efficiency?


It will decrease.
It remains unchanged.
It will increase as a result of the fan speed being raised further.
It will increase.

9

Közepes

What can cause frost to form on the evaporator?


a drop in cooling capacity.
A reduction in the temperature of the cooled substance.
An increase in refrigerant flow resistance and a reduction in the refrigerant flow rate through the evaporator.
Frost build-up on the evaporator increases airflow resistance and, consequently, causes the fan motor to work harder.

10

Közepes

What happens when the evaporation temperature drops?


The compressor’s cooling capacity increases.
The discharge temperature decreases.
The condenser fan speed increases.
The compressor’s cooling capacity decreases.

11

Közepes

When is defrosting using the refrigerant possible?


Only when using speed-controlled fans.
In the case of air-cooled chillers, only when the air temperature is above 0°C.
Never. We use electricity for defrosting (for example, using a special electric heater).
Defrosting using the refrigerant is not possible at all.

12

Közepes

When can frost form on the evaporator surface?


Frost always forms on air coolers.
Frost forms only when the refrigeration system is operating continuously.
Only in the case of air coolers, when the air temperature drops below 0°C.
In the case of finned evaporators.

13

Közepes

In the case of extensive pipework systems, secondary evaporation of the refrigerant can be prevented by...


additional cooling.
using larger-diameter pipes.
using smaller-diameter pipes.
by insulating the pipes between the compressor and the condenser.

14

Közepes

How does hot gas defrosting of the evaporator work?


This involves reversing the direction of rotation of the compressor.
We switch on the gas heater directed at the evaporator.
We swap the outlet and inlet sides of the evaporator.
Heated vapour (hot gas) from the compressor is directed into the evaporator piping.

15

Közepes

What is the function of the evaporator in a refrigeration system?


Thanks to the evaporator, the cooled medium transfers heat to the boiling refrigerant.
It evaporates the water flowing through the evaporator.
It cools the refrigerant.
It ensures that the refrigerant is superheated over the largest possible heat exchange surface area.

16

Közepes

What conditions must be met for the evaporator to be defrosted using electric heaters?


The electric heaters must be positioned beneath the evaporator’s heat exchange surface.
The electric heaters must be in contact with the evaporator’s heat exchange surface (the heater must touch the fins).
The electric heaters must be positioned in direct contact with the refrigerant so that the refrigerant flowing through the evaporator is at a sufficiently high temperature.
Thanks to the forced air flow created by the fans, the heat from the heaters is transferred to the heat exchanger.

17

Közepes

Refrigerant distributor:


ensures even distribution of the refrigerant to the individual sections of the condenser.
ensures the even distribution of the refrigerant discharged by compressors connected in parallel.
ensures an even distribution of the refrigerant to the individual sections of the evaporator.
acts as a buffer for the refrigerant in the event that the pressure upstream of the expansion valve is exceeded.

18

Közepes

What are the possible methods of defrosting air coolers?


Electric defrosting only.
Hot gas defrosting.
Electric defrosting, liquid defrosting or defrosting using hot refrigerant vapour.
Natural defrosting; there are no other effective methods.

19

Közepes

The boiling point increases (and consequently the rate of evaporation increases) if the pressure above the liquid...


Rises.
Falls.
Remains constant.
It behaves differently depending on the ambient temperature.

20

Közepes

MOP in thermostatic expansion valves stands for:


maximum operating pressure.
self-cleaning of the valve in the event of moisture in the refrigerant freezing.
maximum pressure switch protection.
minimum flow opening.

21

Közepes

The function of a thermostatic expansion valve (TEV) in a refrigeration system is:


to consistently adjust the evaporation pressure in the condenser depending on the temperature of the refrigerant vapour leaving the condenser.
to control the amount of refrigerant supplied to the evaporator depending on the superheat of the vapour leaving that heat exchanger.
to maintain a constant suction pressure to the compressor.
regulating the superheat of the refrigerant leaving the evaporator so that it is at the minimum value.

22

Közepes

When using a capillary tube, what type of motor can be used in the compressor?


A low-speed motor should be used.
A motor with high starting torque must be used.
An electronically commutated motor approved for use with the compressor should be used.
A motor with low starting torque can be used.

23

Közepes

What does the thermostatic expansion valve regulate?


Cooling.
The mass flow of the refrigerant injected into the evaporator.
Discharge temperature.
Evaporation pressure after.

24

Közepes

The refrigerant absorbs heat when...


freezes.
it condenses.
it evaporates.
sublimates

25

Közepes

In the case of a thermostatic expansion valve, the manufacturer specifies...


  ...the degree to which the valve is filled with refrigerant liquid.
...the static superheat of the valve.
…the degree of refrigerant expansion.
...the superheat value during valve operation.

26

Közepes

How do we charge a new or repaired system with refrigerant when it is fitted with an expansion valve


to the suction side of the compressor.
in any way.
behind the condenser to the liquid refrigerant receiver.
Charging with refrigerant takes place during operation via the outlet connection of the refrigerant capillary tube.

27

Közepes

What does a thermostatic/electronic expansion valve regulate?


The number of revolutions of the compressor per unit of time.
The evaporation pressure, closing when it falls below the setpoint temperature.
The amount of refrigerant by controlling the evaporator superheat.
Condenser subcooling by adjusting the condensing pressure.

28

Közepes

What does the MOP function in expansion valves mean?


This means that these expansion valves are set to prevent overheating.
This means that these expansion valves are set to a specific suction pressure.
This means that these expansion valves are set to limit subcooling.
It means that these expansion valves are set to limit the maximum operating pressure.

29

Közepes

The lower the temperature of the liquid refrigerant upstream of the expansion valve,


...the lower the theoretical coefficient of refrigeration efficiency qo will be, and the lower the refrigeration capacity Qo will be.
... the higher the theoretical coefficient of cooling capacity qo will be, and the greater the cooling capacity Qo will be.
  ...the lower the theoretical coefficient of cooling efficiency qo will be, whilst the cooling capacity Qo remains unchanged.
...the lower the theoretical coefficient of cooling efficiency qo will be, and the lower the system’s energy efficiency will be.

30

Közepes

The MOP point in the expansion valve, due to the maximum evaporation temperature of the refrigeration system, ...


...must be approximately 7 K lower.
The value of the MOP point is irrelevant.
...must be approximately 7 K higher.
...must be approximately 5 K lower.

31

Közepes

What is the function of the suction pressure regulator?


To maintain the suction pressure at the highest possible level.
It maintains the suction pressure at a constant level.
It limits the suction pressure and protects the compressor from excessively high suction pressure.
It prevents a drop in suction pressure and, if necessary, shuts down the refrigeration system.

32

Közepes

What is the function of the valve regulating water flow through the condenser?


To maintain the condensing pressure at the highest possible level.
To maintain the condensing pressure at a constant level.
To maintain the water temperature at the highest level.
To maintain the condensing pressure at the lowest possible level.

33

Közepes

The use of a refrigerant distributor requires a thermostatic expansion valve …


… with an adsorption-type sensor filling.
… with a MOP function.
… with internal pressure equalisation.
… with external pressure equalisation.

34

Közepes

What properties should good insulation materials have?


It must have a good antistatic coating
It must have a low thermal conductivity.
It must be able to absorb large amounts of moisture.
It must have a high thermal conductivity.

35

Közepes

When do we encounter the superheated state?


It is the temperature difference between the evaporation temperature and the ambient temperature.
This is a state that arises as a result of the temperature difference between the suction side and the discharge side of a compressor.
It is a condition in which the compressor motor temperature rises excessively.
This is the temperature difference between the actual vapour temperature and the vapour temperature at saturation.

36

Közepes

How can you check whether the liquid refrigerant is reaching the expansion valve without vapour bubbles?


We check using a liquid pressure gauge.
We are unable to check this.
We check this using a sight glass.
We check using a pressure gauge fitted on the discharge side of the compressor.

37

Közepes

The liquid lines are located...


between the compressor and the condenser.
between the evaporator and the regenerative heat exchanger.
between the evaporator and the compressor.
between the condenser and the liquid receiver.

38

Közepes

What is the function of the liquid receiver in a refrigeration system?


The tank is used to store and ensure an adequate supply of refrigerant in the event of fluctuations in the thermal load of the refrigeration system.
When an installation technician does not know the exact amount of refrigerant required, the tank serves as a safety reserve for the entire refrigeration system.
The tank is used to collect the liquid refrigerant and excess oil in the system.
The reservoir is used to further cool the liquefied refrigerant leaving the condenser.

39

Közepes

What is the purpose of the liquid refrigerant reservoir?


The tank is used to collect the liquid refrigerant and excess oil in the system.
The tank is required during maintenance work, when there is a temporary need to store the refrigerant that has been circulating in the refrigeration system up to that point.
When an installation technician does not know the exact amount of refrigerant required, the tank serves as a safety reserve for the entire refrigeration system.
The tank is used to further cool the liquefied refrigerant leaving the condenser.

40

Közepes

Where should the liquid receiver be installed?


It should be fitted between the compressor and the condenser.
It should be fitted just before the compressor.
It should be fitted after the evaporator.
It should be installed downstream of the condenser, upstream of the expansion valve.

41

Közepes

What is the function of the suction pressure regulator fitted to the suction pipe when the compressor starts up?


It regulates the condensing pressure.
It regulates the evaporation pressure.
It closes when the suction pressure upstream of the compressor drops.
It opens when the suction pressure upstream of the compressor drops.

42

Közepes

The use of microchannel heat exchangers, compared with conventional heat exchangers made of copper tubes and fins, results in:


A reduction in the system’s energy efficiency.
There is no effect whatsoever on either the amount of refrigerant or energy efficiency.
A reduction in the amount of refrigerant and an increase in energy efficiency.
An increase in the amount of refrigerant in the system and an increase in condensing pressure.

43

Közepes

Which refrigerants belong to the HFC group?


R22, R401A.
R134a, R32, R22, R507A, R290.
R11, R12, R502.
R134a, R404A, R507A, R410A.

44

Közepes

Which refrigerants belong to the HFO group?


R134a, R290.
R134a, R404A.
R22, R12.
R1234yf, R1234ze.

45

Közepes

What are the characteristics of R410A refrigerant compared to R407C refrigerant?


The saturation pressure of both refrigerants is roughly the same.
The saturation pressure of R410A refrigerant is higher than that of R407C.
The saturation pressure of R407C refrigerant is much higher than that of R410A.
The saturation pressure of R407C is 150% higher than that of R410A.

46

Közepes

What does the TEWI parameter define?


This is a parameter defining the ozone layer’s ability to recover (regenerate).
It is the total (global) greenhouse gas equivalent – this indicator takes into account the refrigerant’s direct capacity to contribute to the greenhouse effect and its indirect impact on it through the energy consumption (during the production of which CO₂ is generated) by the refrigeration unit in operation.
This is a parameter that quantifies the impact of refrigerants on the ozone layer.
It is the global warming potential, expressed in terms of carbon dioxide (CO₂), over a 100-year time horizon.

47

Közepes

What are the characteristics of R452A refrigerant compared to R404A?


Both refrigerants are homogeneous refrigerants with no temperature glide.
It is a flammable and toxic homogeneous refrigerant from the HFC group.
It is a non-flammable refrigerant, a mixture from the HFC/HFO group with thermodynamic properties similar to those of R404A and a GWP approximately 45% lower than that of R404A.
The temperature glide of R452A is half that of R404A.

48

Közepes

What is the distinguishing feature of R1234yf compared to R134a?


a higher boiling point at standard pressure.
greater toxicity.
A higher critical temperature.
greater flammability.

49

Közepes

Compared to R134a, the refrigerant CO₂ is characterised by?


It has identical thermodynamic properties and can be used as a drop-in replacement for R134a.
It has a temperature slip of 7K greater than R134a.
Unlike R134a, it is an azeotropic mixture.
It has a lower critical temperature, higher operating pressures and greater volumetric efficiency, allowing for the use of a smaller quantity of refrigerant compared to R134a.

50

Közepes

The following are not classified as fluorinated greenhouse gases:


Perfluorocarbons (PFCs).
Carbon dioxide (CO₂).
Hydrofluorocarbons (HFCs).
Sulphur hexafluoride (SF6).

51

Közepes

What is the greenhouse effect?


It causes the thermal radiation emitted by the Earth to be trapped in the upper atmosphere.
It causes an increase in temperature close to the Earth’s surface (up to 10 metres above the surface).
It lowers the average surface temperature of the Earth.
It alters the composition of the atmospheric air.

52

Könnyű

What does the GWP indicator mean?


It is the global warming potential. The impact on global warming caused by 1 kg of a given gas or chemical substance, expressed as a GWP value, where GWP=1 represents the global warming caused by 1 kg of CO₂ over a period of 100 years (the global warming potential of a unit mass of a given gas over a 100-year period, relative to the warming caused by a unit mass of CO₂).
This is an indicator expressing the potential to deplete the ozone layer.
It is a unit expressing the ability to enhance the ozone layer.
It is an expansion of the abbreviation ‘Global Warming Potential’ and indicates the rate of increase in air temperature

53

Közepes

How do refrigeration systems contribute to the greenhouse effect, i.e. the rise in atmospheric temperature at the Earth’s surface?


Through the leakage of refrigerant into the environment.
Refrigeration equipment emits CO₂ both directly and indirectly.
Indirectly (through energy consumption) and directly (through the emission of refrigerants into the atmosphere)
As a result of oil being emitted into the atmosphere by the condenser and filter

54

Közepes

What is the greenhouse effect, also known as the greenhouse phenomenon?


This is the formation of a layer that traps only the heat generated by the combustion of fuel in aeroplanes.
The filtering out of solar radiation.
The absorption of radiation reaching the Earth’s surface.
It is the phenomenon of heat being trapped in the Earth’s atmosphere (making it difficult for heat to radiate out of the Earth’s atmosphere).

55

Közepes

Which EU regulation is currently the primary piece of legislation governing the use of fluorinated greenhouse gases (F-gases) in the European Union?


Directive 2009/125/EC
Regulation (EU) 2015/1188
Regulation (EU) 2024/573
Regulation (EU) No 517/2014

56

Közepes

What is the main objective of Regulation (EU) 2024/573?


To reduce taxes on refrigeration equipment
Prevention of F-gas emissions and the achievement of the EU’s climate targets
Standardising metal recycling standards
To facilitate the import of electrical appliances

57

Közepes

What are the obligations of manufacturers of refrigeration appliances in the context of ecodesign, and which regulation governs them?


Manufacturers are only required to use energy labels, and this is regulated by Regulation (EU) 2024/573
Manufacturers must comply solely with ISO 9001 standards, without any link to EU regulations
Manufacturers are only required to declare the quantity of F-gas used, in accordance with Regulation (EU) No 517/2014
The manufacturer must ensure minimum energy efficiency, reparability and recyclability of equipment, as regulated by Regulation (EU) 2019/2019

58

Közepes

What is the main objective of the Ecodesign Directive?


To standardise the appearance of products in the EU
To increase sales of electrical appliances in the EU
To facilitate the import of products from outside the EU
Reducing the negative environmental impact of products by improving energy efficiency, durability and recyclability

59

Közepes

What is the function of a ball valve in a refrigeration system?


It regulates the temperature of the refrigerant
It prevents excessive pressure build-up in the system
Enables the refrigerant flow to be completely shut off
It measures the moisture content of the refrigerant

60

Könnyű

What is the main function of a relief valve?


It monitors the moisture content of the refrigerant
It controls the oil level in the compressor
Relieves pressure in the system in the event of excessive pressure
Prevents the evaporator from freezing

61

Közepes

How do certain substances or gases contribute to the greenhouse effect?


Some substances damage the ozone layer
Certain substances limit the impact of the Sun’s ultraviolet radiation on the Earth’s surface.
Certain substances trap the thermal radiation that the Earth should radiate into the atmosphere. In this way, the Earth gradually warms up and the greenhouse effect occurs.
When released into the atmosphere, certain substances cause the air to heat up as a result of reactions with the oxygen and nitrogen contained in the air.

62

Közepes

What is the purpose of the sight glass in a refrigeration system?


For visual assessment of the presence of refrigerant and oil, and for monitoring moisture levels
To shut off the flow in the event of an emergency
To regulate compressor pressure
To measure the condenser temperature

63

Közepes

What is the function of the temperature regulator in a refrigeration system?


It restricts oil flow
Controls the operation of the compressor and valves to maintain the set temperature
It drains excess refrigerant into the receiver
To maintain a constant pressure in the compressor

64

Nehéz

What is the role of the liquid separator in systems using flammable or toxic refrigerants?


It separates the liquid from the oil
They are used solely to measure the moisture content of the refrigerant
It prevents liquid from entering the compressor
Heats the refrigerant before it enters the evaporator

65

Nehéz

What is the function of an oil separator in systems using flammable or toxic refrigerants?


They are used solely to measure the moisture content of the refrigerant
Separates oil from the refrigerant and facilitates the return of oil to the compressor
It prevents liquid from entering the compressor
Heats the refrigerant before it enters the evaporator

66

Közepes

What is the purpose of oil level regulators in a refrigeration system?


They drain off excess refrigerant
They control the evaporator temperature
Maintains the correct oil level in the compressor
They control the pressure in the condenser

67

Közepes

What is the function of the refrigerant receiver in the system?


Regulates the oil flow
It controls the evaporator temperature
Stores excess refrigerant and facilitates the detection of leaks
It maintains a constant pressure in the system

68

Közepes

What is the role of the manifold thermometer in the refrigeration system?


Relieves pressure in the system in the event of excessive pressure
It monitors the moisture content of the refrigerant
Measures the refrigerant temperature at the compressor inlet and outlet, which helps to identify leaks
Controls the oil level

69

Közepes

What is the role of the defrost control valves?


They control the pressure in the compressor
They are used to monitor the moisture content of the refrigerant
They drain off excess oil
Protect the evaporator from excessive icing and reduce the risk of leaks

70

Könnyű

What is the base unit of pressure according to the International System of Units (SI)?


Pa
bar
Psi
Atm.

71

Közepes

Where can I find lists detailing fluorinated greenhouse gases (F-gases)?


In the Regulation of the Minister for the Economy on the introduction of a list of fluorinated greenhouse gases.
In the Act on Ozone-Depleting Substances and Certain Fluorinated Greenhouse Gases.
In Regulation (EU) No 2024/573 of the European Parliament and of the Council
In the Vienna Convention for the Protection of the Ozone Layer.

72

Közepes

Where can I find the lists specifying controlled substances?


In the Regulation of the Minister for the Environment on the list of controlled substances.
In Regulation (EU) No 2024/590 of the European Parliament and of the Council.
In the current Act on Ozone-Depleting Substances and Certain Fluorinated Greenhouse Gases.
In the Vienna Convention for the Protection of the Ozone Layer.

73

Közepes

Where and by when should annual reports on ODS and F-gases be submitted?


Reports must be submitted by the end of the relevant calendar year, using a special form at the regional branch of the Office of Technical Inspection (UDT)
Reports for the previous year must be submitted by 31 January electronically by completing the special forms available in the central register of operators ‘CRO’.
Reports for the previous year must be submitted by 31 March of the relevant year electronically to the Ministry of the Environment.
Reports on ODS and F-gases for the previous year must be submitted by 28 February of the following year, via the IT system available in the reports database at the Office for the Protection of the Ozone Layer and Climate (BOWOiK) on the ICHP website.

74

Közepes

Which measure has the greatest impact on improving the compressor’s energy efficiency during installation?


Installation without a leak test
Increasing the amount of refrigerant
Installation without filters
Correctly create a vacuum and remove moisture from the system

75

Közepes

How does regular monitoring of the oil level affect the compressor’s operation?


It reduces cooling capacity
Causes a rise in pressure
Ensures proper lubrication and improves energy efficiency
It has no effect

76

Közepes

How do system leaks affect the compressor’s energy efficiency?


Have no effect
They lower the operating temperature
These cause a drop in performance and an increase in energy consumption
They improve efficiency

77

Közepes

Regulation (EC) No 2024/590 relates to:


Health and safety at work during the recovery of refrigerants.
Alternative refrigerants serving as substitutes for fluorinated greenhouse gases.
Ozone-depleting substances.
The conditions for obtaining F-gas certificates by companies carrying out the recovery and reclamation of waste refrigerants.

78

Közepes

What is the significance of regulating suction and discharge pressure?


Increases oil consumption
Helps maintain optimal operating conditions for the compressor
Causes leaks
It has no effect on efficiency

79

Közepes

What maintenance measure reduces the compressor’s energy consumption?


Regular replacement of filters and dryers
Disabling safety devices
Lack of servicing
Increasing the refrigerant charge

80

Közepes

How does the presence of air in the refrigeration system affect performance?


Reduces energy consumption
It has no effect
It improves efficiency
Leads to increased pressure and reduced efficiency

81

Közepes

What role do control systems (e.g. regulators) play in compressor efficiency?


It increases the amount of refrigerant
Causes leaks
It doesn’t matter
Enables optimisation of operation and a reduction in energy consumption

82

Közepes

How does refrigerant superheat at the compressor suction affect performance?


Excessive overheating reduces efficiency and increases energy consumption
It always improves performance
It has no effect
It only causes a drop in temperature

83

Közepes

How does the correct layout of the system affect efficiency?


It doesn’t matter
It causes the temperature to rise
It increases the pressure
Shortens flow paths and reduces energy losses

84

Közepes

How important is pipe insulation?


Causes a rise in pressure
It increases energy consumption
It has no effect
Reduces heat loss and improves energy efficiency

85

Közepes

Which measure most improves the condenser’s energy efficiency?


Increasing the amount of refrigerant
Contamination of the heat exchange surface
Restricted airflow
Regular cleaning of heat exchange surfaces

86

Közepes

How does a dirty condenser affect the operation of the refrigeration system?


Causes an increase in pressure and energy consumption by the compressor
It improves efficiency
It has no effect
It lowers the condensing pressure

87

Közepes

Why is adequate airflow through an air-cooled condenser important?


Ensures effective heat dissipation and improves energy efficiency
Causes a drop in pressure
Insufficient airflow reduces efficiency
It doesn’t matter

88

Közepes

Which refrigerants cause damage to the ozone layer?


All refrigerants that are hydrocarbon derivatives.
All refrigerants that contain fluorine and hydrogen in their molecules.
All refrigerants that contain chlorine or bromine in their molecules.
All refrigerants that contain carbon in their molecular structure.

89

Közepes

How does the presence of limescale in a water-cooled condenser affect performance?


Impairs heat exchange and increases energy consumption
It improves heat transfer
It lowers the condensation temperature
It has no effect

90

Közepes

How does correct condensation pressure control affect efficiency?


Maintains optimum operating conditions and reduces energy consumption
It increases energy consumption
Causes leaks
It has no effect

91

Közepes

How do condenser leaks affect energy efficiency?


They improve efficiency
Have no effect
Causes refrigerant loss and a drop in efficiency
They lower the temperature

92

Közepes

How important is the correct positioning of an air-cooled condenser?


It should be housed in a small room
It should be installed in a well-ventilated area with unobstructed airflow
It doesn’t matter
It should be close to heat sources

93

Közepes

How does hot air recirculation affect the condenser?


It improves efficiency
Impairs cooling and increases energy consumption
It has no effect
It reduces the pressure

94

Közepes

How does the insulation of central heating and domestic hot water pipework affect the operation of the heat pump’s condenser?


It doesn’t matter
It increases the pressure
Reduces energy losses and improves the efficiency of the entire system
It impairs cooling

95

Közepes

Which measure most improves the energy efficiency of the evaporator?


Increasing the condensation temperature
Increasing the amount of refrigerant
Regular defrosting of the evaporator
Restricted airflow

96

Közepes

How does evaporator icing affect the system’s operation?


Impairs heat exchange and increases energy consumption
It lowers the condensation temperature
It improves cooling performance
It has no effect

97

Közepes

How does dirt on the evaporator surface affect its performance?


It reduces the pressure
It has no effect
It improves efficiency
Impairs heat exchange and increases energy consumption

98

Közepes

What maintenance task is crucial for the evaporator?


Reduced airflow
Increasing the refrigerant charge
Regular cleaning and defrosting
Lack of maintenance

99

Közepes

What does an F-gas personal certificate (Category A2) authorise?


To recover refrigerant from equipment containing less than 3 kg of fluorinated greenhouse gases, or less than 6 kg in the case of hermetically sealed systems.
to repair, maintain or service refrigeration equipment and systems containing controlled substances.
for the purchase of lubricants and refrigeration oils, and for the testing of safety valves.
to make permanent joints by brazing in systems containing fluorinated greenhouse gases.

100

Közepes

How does superheating of the refrigerant at the evaporator outlet affect efficiency?


Excessive superheat reduces energy efficiency
It always improves performance
It only causes a drop in temperature
It has no effect

101

Közepes

How do leaks in the evaporator affect efficiency?


Increase capacity
Have no effect
Improves performance
These cause refrigerant loss and a drop in efficiency

102

Közepes

How important is correct expansion valve adjustment?


It doesn’t matter
Ensures optimal evaporator charge and improves efficiency
Causes leaks
It increases energy consumption

103

Közepes

How does inadequate insulation of the heat transfer circuit pipes affect evaporator performance?


It improves efficiency
Causes cooling losses and increased energy consumption
It has no effect
It lowers the condensation temperature

104

Közepes

How does correct TEV valve adjustment affect the system’s energy efficiency?


Ensures optimum superheat and improves system efficiency
Causes leaks
It has no effect
It increases energy consumption

105

Közepes

What happens if the superheat set by the TEV is too high?


The refrigerant charge will increase
Efficiency will drop because the evaporator is not being fully utilised
It has no effect
Cooling efficiency will improve

106

Közepes

How does a low superheat setting on the TEV affect performance?


It reduces refrigerant flow
It increases operational safety
It may lead to improved efficiency, but it increases the risk of the compressor becoming flooded with liquid
It has no effect

107

Közepes

How do contaminants in the system affect the operation of the TEV?


They improve its performance
They lower the temperature
Have no effect
They can cause it to become blocked and reduce efficiency

108

Közepes

What role does the filter-drier play in terms of system efficiency?


Removes moisture and contaminants, improving the system’s efficiency
It doesn’t matter
It lowers the temperature
It increases the amount of refrigerant

109

Közepes

How does proper insulation of components (e.g. pipes near the TEV) affect the system?


Prevents unwanted heat gains and improves efficiency
It causes leaks
It doesn’t matter
It increases energy consumption

110

Közepes

What does Regulation (EU) No 2024/573 of the European Parliament and of the Council cover?


The Regulation concerns gases that contribute to the greenhouse effect.
The Regulation concerns leak testing of stationary refrigeration, air-conditioning and heat pump equipment containing fluorinated greenhouse gases. The Regulation sets out the requirements relating to leak testing of such equipment.
The Regulation sets out requirements relating to brazing of refrigeration systems.
The Regulation sets out health and safety requirements for soldering work.

111

Közepes

How important is it to check the operation of the condensing pressure control valve in the system?


Ensures operation within the optimum pressure range and reduces energy losses
It has no effect
It causes a significant rise in temperature
It increases energy consumption

112

Közepes

How does the correct selection of a TEV affect energy efficiency?


It increases the amount of refrigerant
It lowers the temperature
It doesn’t matter
Ensures the system is matched to its capacity and operates optimally

113

Közepes

What is the main design difference in hydrocarbon-based refrigeration systems?


No need for safety measures
Lower energy efficiency
The need for explosion-proof measures due to the flammability of the refrigerant
Higher operating pressures

114

Közepes

What differences are there in the compressors used in hydrocarbon systems?


No differences
They do not require lubrication
They must be designed to operate with flammable refrigerants (e.g. hermetic compressors)
They must operate at higher pressures

115

Közepes

How can one check whether the system has been overcharged with refrigerant?


The compressor will operate under a lower load and the suction pressure will decrease
The refrigeration system is overcharged with refrigerant whilst in operation, and even under a very small heat load, frost forms on the suction side of the compressor
This cannot be checked with sufficient reliability, as the sight glass is not designed for this purpose.
Under normal conditions, there is a marked increase in condensing pressure because an excessive amount of refrigerant accumulates in the condenser, reducing the heat exchange surface area within it.

116

Közepes

Before charging the refrigeration unit with refrigerant, it is essential to…


carry out a start-up test.
check the compressor’s suction and discharge connections.
complete the unit’s data sheet.
carry out a leak test.

117

Közepes

What information must appear on the unit’s label?


Among other things: information stating that the unit contains a fluorinated greenhouse gas, together with the industrial designation of the gas or its chemical name, the mass of the gas and its CO₂ equivalent
It does not matter what should be included on the device label.
Markings regarding the weight and capacity of the pipework, together with the colour code and chemical composition of the paints used to coat the frame and casing.
The manufacturer’s logo and the weight of the unit.

118

Közepes

What is the base unit of temperature according to the International System of Units (Système International d’Unités)?


°R
K
°F
°C

119

Közepes

Which of the following are the most important pieces of information that should be included in the unit’s data sheet:


Operator details, unit details, type and quantity of refrigerant, information regarding servicing and repairs.
Information regarding refrigerant recovery and unit dismantling.
The owner, installer and service technician of the unit.
The make and model of the unit, so that the manufacturer can be contacted to obtain the technical information necessary for servicing.

120

Közepes

Who is responsible for drawing up the equipment or installation record?


The equipment maintenance technician.
There is no such obligation.
The operator of the unit or system.
The person responsible for risk assessment.

121

Közepes

Oil traps on the suction pipework are required:


before the safety valve.
always before any rise in the pipeline.
before the compressor.
at the inlet to each component of the refrigeration system.

122

Közepes

When is there a refrigerant leak, even though the compressor is still running?


When we observe a rise in the refrigerant level in the liquid receiver and the subcooling increases.
When the sight glass is full of liquid refrigerant and we observe a rise in the oil level in the compressor sump.
When the condensing pressure and suction pressure rise, but there is no superheat.
When the suction pressure is low, superheat is high, subcooling is negligible and the temperature difference between the condenser and the expansion valve is small.

123

Közepes

Which components of a refrigeration system can be classified as potential leak points (leaks) subject to regular leak tests?


Fittings, valves including their stems, seals – including those in replaceable filters and dryers, components exposed to vibration, and connections to measuring, control and safety devices.
Parts of the system located on the high-pressure side (from the compressor up to and including the expansion valve).
All parts of the refrigeration unit that are connected to the suction side of the refrigeration system.
Hermetic compressors, liquid refrigerant tanks and liquid separators.

124

Közepes

What is the test pressure during the pressure leak test of the unit?


According to the PN-EN 378 standard, at least 0.25 times the maximum permissible pressure for the system (PS).
The test pressure for leak testing is equivalent to the maximum operating pressure measured during the operation of the refrigeration unit.
The test pressure is determined by the person carrying out the leak test based on their experience.
The test pressure (maximum) is 30 bar.

125

Közepes

In which part of the refrigeration unit must the recommended leak test be carried out?


The test must be carried out at all points on the refrigeration unit where there is a potential risk of refrigerant leakage.
The check must be carried out on all parts of the refrigeration system that are connected to the discharge side of the refrigeration circuit.
The check should only be carried out at the connection points for measuring instruments (pressure switches, pressure gauges, temperature sensors).
The test must be carried out on the compressor shut-off valves, solenoid valves and filters.

126

Közepes

When can a given unit be considered perfectly leak-tight?


A given unit can be considered perfectly leak-tight if, during a leak test, the pressure remains constant, taking into account pressure changes caused by temperature variations. Any drop in pressure indicates a leak and requires the location of the leak to be identified.
A device can be considered perfectly leak-tight if gas bubbles appear when it is submerged in water.
A given device can be considered perfectly leak-tight when the pressure drop during the test does not exceed 0.1 bar.
The device in question is perfectly leak-tight when we have carried out a check using a permanently installed electronic detector.

127

Közepes

What does EU Regulation 1516/2007 cover?


The Regulation addresses the disposal of gases that contribute to the greenhouse effect.
The Regulation sets out health and safety requirements for soldering work.
The Regulation concerns leak testing of stationary refrigeration, air-conditioning and heat pump equipment containing fluorinated greenhouse gases. The Regulation sets out the requirements for leak testing of such equipment.
The Regulation sets out requirements relating to brazing of refrigeration systems.

128

Nehéz

Which parts of refrigeration systems must be inspected on a mandatory and regular basis in accordance with EU Regulation 1516/2007?


Connections on the condenser, as there is high pressure and the refrigerant is in liquid form
Fittings, 2. valves, 3. seals, 4. parts/components exposed to vibration, 5. connections at safety devices.
Compressor connections, 2. connections on the liquid refrigerant tank
Only compressor connections, as these are subject to vibration.

129

Könnyű

What is superheat?


It is the amount of heat required to increase the pressure.
It is the amount of heat required to turn a liquid into vapour.
It is the amount of heat required to heat a liquid.
It is the amount of heat required to cause the vapour formed from a liquid to become superheated.

130

Nehéz

In accordance with EU Regulation 1516/2007, there are several methods of leak testing. What are these methods called?


We distinguish between quality control methods for supplied materials and electronic testing methods.
We distinguish between direct and indirect methods of leak detection.
We distinguish between methods for quality control of supplied materials and leak testing methods that do not involve quality control of supplied materials.
We distinguish between physical and chemical methods.

131

Nehéz

In accordance with EU Regulation 1516/2007, to whom can we entrust the responsibilities for leak testing of refrigeration systems?


The check may be carried out by a specialist in leak testing.
The test may only be carried out by a competent person with the relevant skills, who holds a certificate attesting to the necessary knowledge in this field. They must also hold a certificate for companies regarding the operation and maintenance of refrigeration equipment charged with F-gases.
The check may only be carried out by a person who has previously carried out such a check.
The inspection may be carried out by a person employed and appointed by the owner of the installation.

132

Nehéz

In accordance with EU Regulation 1516/2007, what conditions must be met in order to carry out a leak test on refrigeration systems using ultraviolet (UV) light?


A prerequisite for carrying out the inspection is holding the relevant authorisation for pressure testing issued by the UDT.
A prerequisite for carrying out a leak test using UV is having the appropriate technical resources, the relevant materials supplied, and suitable safety goggles.
A prerequisite for carrying out a leak test using UV is that such a test is technically feasible.
The manufacturer of the refrigeration equipment must confirm that the aforementioned UV method can be used. A UV leak test may be carried out by a qualified person who holds the relevant qualifications (certificate).

133

Nehéz

In accordance with EU Regulation 1516/2007, which leak testing methods are classified as direct leak testing methods?


Detection of leaks using a handheld leak detector and/or a fixed leak detection system; 2. Detection of leaks using a special dye with UV-fluorescent properties; 3. Detection of leaks using a foaming solution.
Leak test following the creation of a vacuum and leak detection using a foaming solution.
Leak testing by measuring pressure changes and the method of submerging the device/system in water.
Leak test using nitrogen with a tracer gas, an electronic detector and pressure measurement.

134

Nehéz

In accordance with EU Regulation 1516/2007, which methods are classified as indirect leak testing methods?


It utilises pressure and temperature measurements, as well as an ultrasonic method.
This method is based on electronic leak detection.
Leak detection using a UV tracer.
This method is based on the analysis of the following parameters: pressure, temperature, operating pressure, liquid level, oil leakage, etc.

135

Közepes

How should the pressure be increased during a pressure leak test?


We increase the pressure in any way.
We increase the pressure gradually whilst checking for leaks, until the test pressure is reached, at a rate of no more than 2 bar/min
We increase the pressure at a rate of 10 bar/s.
We increase the pressure as quickly as possible.

136

Közepes

What electronic equipment should be used to carry out leak testing?


Only with devices fitted with an ‘Ion Pump’ sensor.
Only using devices with verified measurement sensitivity.
Only with devices fitted with an infrared detector.
Only with devices fitted with hot cathodes.

137

Közepes

What documentation should be checked before starting a leak test?


Check the operating instructions for the machine/equipment.
Check the time sheets of the staff responsible for the machinery/equipment.
Check the stock ledger (accounts).
The maintenance log and the machine/device operating instructions must be checked.

138

Közepes

What information must be recorded when drawing up the leak test report?


The number of locations where leaks have occurred and the date of the inspection.
The method used to carry out the leak test, the number of faults, the method of repairing the faults, the time taken to work on the installation, and the cost of the repair.
The date of the inspection, a record of the occurrence of the leak, and a signature.
The date of the inspection, the number of faults (leaks), the location of the faults (leaks), the proposed method of rectifying the fault/defect (leak), attached documents and a signature.

139

Közepes

What pressure values should be used for the pressure leak test?


The pressure for the leak test is 2–3 bar.
The pressure value for the leak test is 10–12 bar.
Use a pressure not exceeding the maximum permissible pressure for the system (PS).
At the discretion of the person authorised to carry out the pressure test.

140

Közepes

What is temperature slip?


It involves an increase in temperature.
A specific temperature cannot be assigned to a given vapour pressure. There is a temperature difference between the start and end of evaporation.
It involves a decrease in temperature.
A specific temperature corresponds to a given vapour pressure.

141

Nehéz

What does a vacuum leak test involve?


After switching off the vacuum pump, we check whether the pressure in the system rises
With the vacuum pump running continuously, we are able to maintain the required vacuum level in the system.
If the pressure in the refrigeration system were to rise, we switch on the vacuum pump as required.
With the vacuum pump switched on, check whether the pressure in the system rises as a result of a leak.

142

Nehéz

How often should leak tests be carried out on equipment containing 1.5 kg of R404A refrigerant (5.9 tonnes of CO₂ equivalent)?


At least once every 12 months.
On initial commissioning.
Only when servicing the unit.
Once every six months.

143

Nehéz

How often should leak tests be carried out on equipment containing 7 kg of R404A refrigerant (27.45 tonnes of CO₂ equivalent)?


At least once every 12 months.
On initial commissioning.
Once every six months.
Only when servicing the unit.

144

Közepes

In which appliances and systems is the installation of a permanent leak detection system required?


In equipment and systems containing at least 500 tonnes of CO₂ equivalent.
In equipment and installations containing at least 30 kg of fluorinated greenhouse gases.
In equipment and systems containing at least 50 tonnes of CO₂ equivalent.
In equipment and systems containing at least 5 tonnes of CO₂ equivalent.

145

Nehéz

In accordance with Regulation (EU) 2024/573 of the European Parliament and of the Council, a fixed leak detection system is required when:


The charge of an F-gas refrigerant in a refrigeration unit is at least 500 tonnes of CO₂ equivalent.
The installation of a fixed leak detection system is optional, but it helps to reduce the number of leak checks required on the equipment each year.
The refrigerant charge of the refrigeration equipment is at least 100 kg of ODS.
The refrigeration equipment is operated in an enclosed space.

146

Nehéz

Under Regulation (EC) No 1516/2007 and the F-gas Act, which leak detection methods may not be carried out by a person holding a Category E certificate?


Leak testing using a fluorescent dye.
Leak detection using a foaming solution.
Measuring leaks using a handheld leak detector.
Visual leak inspection.

147

Nehéz

According to the current regulation, what sensitivity must a handheld leak detector have?


8 g/year.
5 g/year.
10 g/year.
3 g/year.

148

Közepes

Which category of F-gas certificate (A1, A2, B, C, D, E) authorises the performance of leak tests on refrigeration equipment:


Category E only.
All except category D.
Only categories A1 and A2.
Categories D and E.

149

Nehéz

Within what timeframe must a leak test be carried out on a stationary refrigeration system after a leak has been repaired, in accordance with EU Regulation 2024/573 on F-gases?


At the next periodic inspection.
Between 24 hours and 1 month after the repair.
At any time.
Immediately after the repair.

150

Nehéz

At what intervals should leak tests be carried out on refrigeration equipment containing more than 500 tonnes of CO₂ equivalent of fluorinated greenhouse gases that does not have a leak detection system installed?


Once a month.
Once every 12 months.
Once every 3 months.
Once every 6 months.

151

Közepes

Why is it advisable to subcool the liquid refrigerant?


This is advisable because it ensures that the liquid refrigerant, free of vapour bubbles, enters the expansion valve.
This is advisable because it allows a smaller evaporator to be used (lower refrigerant temperature at the evaporator inlet).
This is advisable because it allows a smaller condenser to be used (smaller heat exchange surface area).
This is advisable because it allows a smaller expansion valve to be used (less superheat at the valve).

152

Közepes

What should be done following repairs to a leak in the refrigeration unit of a refrigerated trailer?


An invoice for the service work carried out must be issued as soon as possible.
You must enter the details into the equipment log (including the quantities of refrigerant recovered and used) and inform the Operator that an additional leak test must be carried out by a certified person within one month of the repair.
The unit must be charged with an alternative refrigerant, started up, and the refrigerant parameters checked at the service valve located on the liquid receiver.
A visual inspection should be carried out only on bolted and soldered joints.

153

Közepes

Recovery of fluorinated greenhouse gases means:


The reprocessing of fluorinated greenhouse gases to achieve their specified standard properties.
The collection and storage of fluorinated greenhouse gases originating, for example, from machinery, equipment and containers.
The reuse of fluorinated greenhouse gases following a basic purification process.
The final decommissioning and withdrawal from service or use of a product or piece of equipment containing fluorinated greenhouse gases.

154

Közepes

Who is authorised to recover refrigerant from stationary refrigeration equipment:


A service technician holding an F-gas certificate in the relevant category.
The administrator of the operator’s account.
The operator.
The owner of the installation.

155

Közepes

Recovered refrigerants must be stored:


In a specially adapted and labelled cylinder fitted with a two-way valve.
In a cylinder that previously contained the same type of refrigerant.
In any pressure vessel that has been officially certified.
In any used refrigerant cylinder.

156

Közepes

When should the recovery of fluorinated greenhouse gases be carried out:


Before each leak test of the equipment.
Only prior to the final disposal of equipment.
Always during servicing and maintenance of equipment.
Before the final disposal of equipment and, where applicable, during its servicing and maintenance.

157

Közepes

What should be done if the refrigerant recovered from the system is contaminated, e.g. with acid, air or moisture?


You should attempt to purify the mixture yourself using a dehydrating filter.
Add a special contaminant neutraliser to the mixture.
Such a mixture must be handed over to a specialist authorised company for regeneration or disposal.
Purify the mixture by passing it through a particulate filter and reuse it.

158

Közepes

What should be done if different types of refrigerants become mixed in a storage cylinder (container)?


The mixture should be purified by passing it through a filter-drain and reused.
Add a special refrigerant to the mixture.
Send this mixture to a specialist authorised company to have it neutralised.
You should attempt to separate the mixture into its individual components.

159

Közepes

How does refrigerant recovery using the Push-Pull method work?


It involves using a recovery unit to draw (pull) the refrigerant vapour from the cylinder and then force it (push) into the low-pressure side of the system.
This involves the refrigerant being alternately drawn from the suction side and then from the discharge side of the refrigeration unit (compressor).
This involves injecting nitrogen from the cylinder into the unit and expelling the liquid refrigerant from the unit.
This involves using a suction device (compressor) to ensure that the refrigerant, in liquid form, is transferred into the cylinder.

160

Közepes

What are the methods for managing waste refrigerant?


Recovery, disposal.
Recycling, regeneration, disposal.
Regeneration, recovery.
Disposal, storage.

161

Közepes

The most advantageous method of managing waste refrigerant is:


Disposal.
Regeneration.
Storage.
Recycling.

162

Közepes

The lower the evaporation temperature, ...


...the greater the density of the refrigerant and the mass flow rate of the flowing refrigerant.
…the greater the density of the refrigerant and the lower the mass flow rate of the refrigerant.
...the lower the refrigerant density, and the greater the cooling capacity of the compressor.
...the lower the density of the refrigerant and the lower the mass of the flowing refrigerant.

163

Közepes

How should pressure vessels (e.g. refrigerant cylinders) be marked?


They should bear the manufacturer’s logo and the date of manufacture.
It is irrelevant how pressure vessels should be marked.
They should bear, amongst other things, information such as: the number of the standard applied to their design, construction and testing; the identification marks of the country of approval and the inspection body; the date of the acceptance test; and the manufacturer’s and operational marks.
They should bear only markings relating to weight and capacity.

164

Közepes

The recovery of refrigerants does not require the use of:


A refrigerant recovery station.
An electronic leak detector.
Scales with a measurement range suitable for the size of the cylinder being filled.
Hoses with shut-off valves.

165

Közepes

What functions does the compressor perform in a refrigeration system?


The compressor condenses the refrigerant.
The compressor draws in refrigerant vapour from the evaporator, compresses it, and then forces it into the condenser, raising the pressure to the required condensing pressure.
The compressor compresses ambient air and increases the pressure of the refrigerant.
The compressor creates a vacuum on the suction side of the system

166

Könnyű

What is the compressor’s compression ratio?


It is the ratio of the discharge pressure to the suction pressure of the compressor (pk/po).
It is the ratio of the discharge pressure to the effective capacity of the compressor (p/Vk).
It is the amount of refrigerant that will be compressed in a single compressor cycle relative to the heat capacity.
It is the ratio of the suction pressure to the discharge pressure of the compressor (po/pk).

167

Közepes

What is compressor flooding?


Flooding of the compressor due to rainfall.
Suction of liquid refrigerant into the compressor’s suction line.
A large amount of liquid refrigerant in the evaporator.
Flooding the compression chamber with liquid refrigerant or oil.

168

Közepes

To what extent do we regulate the compressor motor’s rotational speed when using a frequency converter?


Up to a maximum of 10 per cent.
From approximately 30% to 90% of capacity.
Approximately from 30 to 75 Hz, which corresponds to around 60% to 150% of the cooling capacity.
Regulating the compressor motor speed is not the same as regulating the cooling capacity.

169

Könnyű

What is the theoretical displacement of a compressor?


It is the volume of refrigerant delivered by a reciprocating compressor per unit of time, usually referred to by the manufacturer as the displacement. It depends on the compressor’s geometric dimensions and rotational speed.
The displacement of a compressor is determined by the dimensions of the cylinder – its volume (cm³)
This is the volume of refrigerant that flows through a reciprocating compressor during a single piston cycle.
The displacement capacity of a compressor is expressed by the coefficient of performance (COP)

170

Közepes

Why is it essential to observe the correct phase sequence for scroll compressors and screw compressors?


Because this type of compressor has difficulty starting up if the phase sequence is changed.
Because the motor speed would decrease, and consequently the compressor’s capacity.
Because these types of compressors are sensitive to voltage drops.
Because changing the phase sequence would reverse the direction of rotation of the compressor rotors, which could result in damage to the compressors.

171

Közepes

The cycle of a two-stage vapour-compression refrigeration system should have, in each stage of the system:


a compression ratio of less than 6
a compression ratio of less than 18.
a compression ratio greater than 8.
a compression ratio of less than 8.

172

Közepes

Why is it necessary to seal the shafts in gland-sealed refrigeration compressors?


Because it ensures the bearing remains lubricated.
Because it prevents oil leakage.
Because it protects the compressor’s crankshaft bearing.
Because we need to prevent air from entering the compressor and we need to prevent refrigerant from leaking from the compressor.

173

Közepes

When is the refrigerant sufficiently cooled?


When the evaporator is covered in frost.
When the outlet from the condenser is cold.
When the liquid distributors are warm.
When no vapour bubbles are observed forming in the liquid sight glass.

174

Közepes

Why should the compressor crankcase be heated?


Heating prevents the refrigerant from dissolving in the oil.
Heating improves the dissolution of the refrigerant in the oil, which is beneficial for its viscosity.
Heating keeps the lubricating oil in a liquid state.
Heating ensures that the lubricating oil is de-watered.

175

Könnyű

What is the dead volume of a compressor?


It is the space between the valve plate and the top of the piston.
This is the space between the bottom of the piston and the crankshaft cover.
It is the space between the valve plate and the bottom dead centre of the piston.
This is the space between the side surface of the piston and the cylinder.

176

Közepes

What are compressor sets?


These are units consisting of two-stage compressors.
These are multiple (several) air-cooled condensers.
These are sets comprising several compressors connected in any configuration.
These consist of a larger number (several) of compressors connected in parallel and mounted on a common frame.

177

Közepes

What are the advantages of compressor units?


These are inexpensive and easy-to-install units.
The ability to adjust the cooling capacity as required.
Space-saving and lower energy consumption.
Easy modification of the system.

178

Közepes

What do we mean by the ‘application range’ of a compressor?


By this term, we mean that the compressor’s operating range is determined by the evaporation temperature ‘to’ during operation.
By this term, we mean the following parameters: compressor capacity, type of refrigerant, and the compressor’s geometric dimensions.
By this term, we mean the following parameters: the evaporation and condensation temperatures (to and tk), or the pressure values that determine the compressor’s application.
By this term, we mean that the compressor’s application range is determined by the evaporation temperature ‘to’ at a given ambient temperature.

179

Közepes

What are the basic functions of oil in a compressor?


The oil seals any leaks that develop in the system.
The oil absorbs moisture from the refrigerant that enters the compressor.
The oil lubricates both the bearings and the sliding surfaces of the compressor components, and cools the compressor by transferring the heat generated during compression to the compressor’s outer casing.
The oil seals the gap between the piston and the cylinder.

180

Közepes

What are the most effective ways of regulating the compressor’s cooling capacity?


By changing the compressor’s displacement, by varying the rotational speed, or by deactivating individual cylinders.
By means of pressure control valves.
By partially covering the evaporator to reduce the heat exchange surface area.
Using an expansion valve.

181

Közepes

What does compressor bypass control involve?


High-pressure liquid refrigerant is injected on the suction side of the compressor.
Refrigerant in the form of cooled, high-pressure vapour is introduced into the suction line.
Hot, high-pressure refrigerant vapour is drawn in on the suction side of the compressor.
The bypass control is not used to regulate the compressor.

182

Közepes

What is the fundamental difference between hermetic and semi-hermetic compressors?


Both types of compressors are disassemblable, and the difference lies in their varying capacities.
The casing of semi-hermetic compressors can be dismantled, whereas the casing of hermetic compressors cannot be dismantled.
Semi-hermetic compressors are characterised by the quiet operation of the entire unit.
The housing of a hermetic compressor and the compressor itself form a single unit.

183

Közepes

How does a scroll compressor work?


It is a type of piston-type device.
It is a device fitted with two spirals. It is a type of positive displacement (volumetric) compressor in which compression takes place through the interaction of the two spirals.
A scroll compressor is also known as a turbo compressor.
It uses two screws to compress the refrigerant.

184

Közepes

What physical process takes place in the evaporator?


The liquid refrigerant evaporates and a small amount of it becomes superheated.
It causes the refrigerant flowing through it to condense.
It cools the refrigerant flowing through it.
The medium flowing through the evaporator (glycol, water) evaporates, whilst the refrigerant condenses.

185

Közepes

What is the purpose of regulating the compressor’s capacity?


It ensures adequate lubrication of the compressor.
Capacity control protects the compressor from low thermal loads.
It allows the cooling capacity to be adjusted to meet requirements.
It ensures that the cooling capacity is adjusted based on condensing temperatures.

186

Közepes

Why is inverter speed control suitable for refrigeration compressors?


Inverter speed control enables continuous, smooth regulation of cooling capacity.
Inverter speed control can be used with any type of compressor to ensure adequate lubrication.
By reducing the speed of the refrigeration compressor motor, inverter speed control improves the return oil flow to the compressor.
Inverter speed control reduces energy consumption only under natural conditions.

187

Közepes

Does the suction gas temperature affect the cooling capacity of the compressor?


It does, but only for reciprocating compressors.
It does, but only if the gas is deeply cooled.
Temperature has no effect on the compressor’s cooling capacity.
It has a significant effect on performance.

188

Közepes

In the case of compressor units fitted with an oil level control system, is it necessary to install the compressors at the same height?


Only scroll compressors.
Yes.
No.
Only screw compressors.

189

Közepes

What functions does a compressor powered by the vehicle’s engine perform in a transport refrigeration system?


This compressor draws in refrigerant vapour from the evaporator, compresses it and then forces it into the condenser whilst the vehicle’s engine is running.
The compressor compresses ambient air and increases the pressure of the refrigerant.
This compressor condenses the refrigerant whilst the vehicle is in motion.
This compressor creates a vacuum on the suction side of the system whilst the vehicle’s engine is switched off.

190

Közepes

Which natural fluids absorb heat from the refrigerant in the condenser?


Water or air.
Ammonia
Air and CO2.
Water and an antifreeze mixture.

191

Közepes

What is the function of the condenser in refrigeration systems?


The heat absorbed in the evaporator and transferred during the compression process is then released into the environment via the condenser.
The heat absorbed in the evaporator is then released into the environment via the condenser
Heat released in the regenerative heat exchanger is absorbed by the condenser.
Heat from the compressor is then released into the environment via the condenser.

192

Közepes

If the condensation temperature is higher than the critical point temperature of the refrigerant, condensation:


temperature has no effect on condensation.
will always occur regardless of the temperature.
will occur provided a specially designed condenser is used.
will not occur.

193

Közepes

How does the subcooling of the refrigerant take place within a refrigeration system?


Subcooling of the refrigerant using oil (dissolving the refrigerant in oil).
Subcooling of the liquid refrigerant in the final section of the condenser.
Subcooling using high-pressure hot vapour.
Subcooling using an additional heat exchanger and liquid nitrogen.

194

Közepes

What is the purpose of controlling the condenser fan speed?


Condenser fan speed control reduces energy efficiency.
Dispersion of the refrigerant in the event of a system leak.
Condenser fan speed control ensures that the condensing pressure is maintained at the correct level.
Condenser fan speed control safeguards against the maximum permissible condensing pressure.